This engine produces 95 horsepower in streetable form.
| DONOVAN MODEL D MACHINEWORK & LABOR | |||||||||
| DESCRIPTION | |||||||||
| ENGINE BLUEPRINT & ASSEMBLY LABOR | |||||||||
| MACHINE FLYWHEEL FOR V-8 PRESSUREPLATE | |||||||||
| DRILL EXTRA CRANKSHAFT MOUNTING HOLES IN FLYWHEEL FLANGE | |||||||||
| INSTALL FLYWHEEL RING GEAR | |||||||||
| UPS PARTS TO & FROM HOUSTON FOR TEFLON COATINGS | |||||||||
| TEFLON COAT SKIRTS & CERAMIC TOPS 4 PISTONS | |||||||||
| REBUILD OIL PUMP & WELD &TURN, MODIFY TO DONOVANS SPECS | |||||||||
| WELD & TURN PUMP DRIVE HOUSING TO SEAL OIL PASSAGE | |||||||||
| MODIFY OIL PAN TO FIT DONOVAN BLOCK | |||||||||
| HONE CYLINDERS TO FIT PISTONS | |||||||||
| BRUSH FINISH CYLINDER WALLS | |||||||||
| BALANCE RODS | |||||||||
| BALANCE PISTONS & PINS | |||||||||
| 3 ANGLE VALVE JOB | |||||||||
| LAP VALVES | |||||||||
| INSTALL CAM BEARINGS | |||||||||
| MACHINE COMBUSTION CHAMBERS TO CLEAR VALVES | |||||||||
| C.C. DONOVAN HEAD | |||||||||
| BALANCE CRANK,FLYWHEEL,PULLEY&CLUTCH ASSEMBLY | |||||||||
| ADD EXTRA OIL PAN BOLT HOLES | |||||||||
| MODIFY SIDE COVER FOR OIL PRESSURE RELIEF VALVE | |||||||||
| PLUMB OIL SYSTEM WITH STAINLESS LINE | |||||||||
| CHAMFER CYLINDERS | |||||||||
| CHAMFER BOTH SIDES ROD BEARINGS | |||||||||
| MAKE CUSTOM TIMING PIN | |||||||||
| HONE FRONT PULLEY TO FIT CRANK SNOUT | |||||||||
| DRILL REAR MAIN BEARING OIL HOLE TO MATCH BLOCK | |||||||||
| DRILL & TAP MAIN OIL PASSAGE IN BLOCK FOR #8 OUTLET FITTING & O-RING | |||||||||
| MACHINE INTAKE MANIFOLD MOUNTING FLANGE TO FIT FOR HEADER | |||||||||
| MAKE WEBER CARBURETOR TO MANIFOLD ADAPTOR | |||||||||
| NOTCH OIL PAN TO CLEAR RODS | |||||||||
| CUT OIL BAFFLE PLATE FOR PRESSURE FED RODS | |||||||||
| MAKE SPRING LOCATING CUP FOR INTERMEDIATE DRIVE RETAINING SPRING | |||||||||
| MAKE REAR CAM PLUG | |||||||||
| ASSEMBLE NEW WATERPUMP | |||||||||
| DONOVAN MODEL D ENGINE PARTS | |||||||||
| QUANITY | PART # | DESCRIPTION | |||||||
| 1 | MODEL D DONOVAN ALUMINUM BLOCK | ||||||||
| 1 | MODEL D ALUMINUM HEAD | ||||||||
| 1 | CROWER BILLIT CRANKSHAFT | ||||||||
| 1 | SET OF 4 BILLIT STEEL RODS | ||||||||
| 1 | CAM BEARING SET | ||||||||
| 1 | HEAD STUD SET | ||||||||
| 1 | ALUMINUM FRONT COVER | ||||||||
| 1 | ALUMINUM SIDE GEAR COVER | ||||||||
| 1 | ALUMINUM TAPPET COVER | ||||||||
| 1 | INTAKE MANIFOLD, SINGLE CARB | ||||||||
| 4 | STAINLESS STEEL INTAKE VALVE | ||||||||
| 4 | STAINLESS STEEL EXHAUST VALVE | ||||||||
| 1 | REMOTE OIL FILTER ADAPTOR | ||||||||
| 1 | VALVE SPRING CUPS | ||||||||
| 1 | UPS DONOVAN | ||||||||
| 1 | A-6256-B | BRONZE CAM GEAR | |||||||
| 1 | A-6306-B | BILLIT STEEL CRANK GEAR | |||||||
| 1 | A-6259-A | CAM NUT | |||||||
| 1 | A-6319-A | CRANK RATCHET BOLT | |||||||
| 1 | A-6312-A | FRONT PULLEY | |||||||
| 1 | A-6314 | TIMING SCALE | |||||||
| 1 | 455/456 | ISKY VALVE SPRING SET | |||||||
| 1 | 707-ST | ISKY STEEL RETAINER SET | |||||||
| 1 | UPS ISKY | ||||||||
| 1 | A-6517 | VALVE KEEPER SET | |||||||
| 1 | A-6307 | CRANKSHAFT KEY | |||||||
| 1 | A-6560 | OIL PUMP DRIVE HOUSING | |||||||
| 1 | A-6551 | OIL PUMP DRIVE GEAR | |||||||
| 1 | A-6561 | OIL PUMP DRIVE SLEEVE | |||||||
| 1 | A-6570 | OIL PUMP DRIVE RETAINING SPRING | |||||||
| 1 | OIL PUMP CORE | ||||||||
| 1 | A-6600 | OIL PUMP REBUILD KIT | |||||||
| 1 | A-6337-C | 350 REAR SEAL | |||||||
| 1 | CRANE F-220/320-12 | ||||||||
| 1 | HARD CHROMED 5 JOURNAL CAMSHAFT | ||||||||
| 1 | A-6623 | OIL PUMP SCREEN | |||||||
| 1 | USED FLYWHEEL | ||||||||
| 1 | A-6620 | OIL PUMP RETAINING SPRING | |||||||
| 1 | A-6310 | CRANKSHAFT OIL SLINGER | |||||||
| 1 | A-6023-A | TIMING PIN | |||||||
| 1 | A-6023-X | TIMING PIN GASKET | |||||||
| 1 | A-6700-M | FRONT SEAL | |||||||
| 1 | A-6750 | DIP STICK | |||||||
| 1 | A-6763 | OIL FILLER TUBE | |||||||
| 1 | A-6766-P | OIL FILLER CAP | |||||||
| 1 | ADJUSTABLE LIFTER SET | ||||||||
| 1 | UPS LIFTERS | ||||||||
| 4 | 390164 | ||||||||
| 1 | UPS ARIAS | ||||||||
| 1 | A-6149-M | RING SET | |||||||
| 1 | MS909P-STD | CLEVITE MAIN BEARING | |||||||
| 4 | CB-745P-STD | CLEVITE ROD BEARING | |||||||
| 1 | A-6676-C | OIL PAN BOLT SET | |||||||
| 1 | 6002 | OIL PRESSURE RELIEF VALVE | |||||||
| 1 | 938-6 | #6 FEMALE T FITING | |||||||
| 2 | 815-6 | #6 UNION & O-RING | |||||||
| 1 | 832-6-8 | #6 TO #8 ADAPTOR, NUT & O-RINGS | |||||||
| 1 | A-6018-X | FRONT SIDE COVER BOLT SET | |||||||
| 4 | 819-6 | #6 LINE SLEEVE | |||||||
| 4 | 818-6 | #6 LINE NUT | |||||||
| 1 | A-8505-XS | STAINLESS WATERPUMP STUD SET | |||||||
| 18 | 1/4 X 3/4 FERRY CAP BOLT | ||||||||
| 4 | 5/16 X 1.25 | CARB MOUNTING STUD | |||||||
| 4 | 5/16 FINE | FLANGE NUT | |||||||
| 1 | B-6008-B | GASKET SET | |||||||
| 1 | DONOVAN CAM THRUST BEARING | ||||||||
| 1 | DONOVAN TAPPET COVER GASKET | ||||||||
| 1 | A-6019 | FRONT COVER BOLT SET | |||||||
| 1 | A-6001-S | RUSTOLEUM BLACK PAINT | |||||||
| 1 | A-8250-B | WATER OUTLET NECK | |||||||
| 1 | 0X3952301 | OIL FILTER ADAPTOR | |||||||
| 2 | 39516644 | OIL FILTER ADAPTOR BOLTS | |||||||
| 1 | A-6730-B | OIL PAN DRAIN PLUG | |||||||
| 1 | A-12249 | DISTRIBUTOR DRIVE SHAFT | |||||||
| 1 | USED MODEL A OIL PAN | ||||||||
| 1 | 22680.01 | WEBER CARBURETOR | |||||||
| 1 | 99217.332S | AIR CLEANER | |||||||
| 1 | A-7563-V | V-8 PRESSURE PLATE | |||||||
| 1 | A-7563-VB | PRESSURE PLATE BOLT SET | |||||||
| 1 | A-6384 | FLYWHEEL RING GEAR | |||||||
| 1 | A-7550 | CLUTCH DISK | |||||||
| 1 | A-7600-L | FLYWHEEL PILOT BEARING | |||||||
| 1 | A-8501-BC | LEAKLESS WATERPUMP | |||||||
| 1 | 51061 | WIX OIL FILTER | |||||||
| 4 | N12YC | CHAMPION SPARK PLUGS | |||||||
| 6 | T50W | TORCO 50 WT. RACING OIL | |||||||
| 2 | IDLE JET | ||||||||
| 2 | MAIN JET | ||||||||
| 1 | AIR CORRECTOR JET | ||||||||